Since The arrival of the first chop saw, miter saws have become more sophisticated, more popular and more useful. In actuality, where precision crosscuts and accurate miters are involved, there’s scarcely a better instrument than a miter saw. Allowing users to work faster and with much greater precision, to perform compound miter cuts, bevel cuts and to utilize larger pieces of material, the multipurpose miter saw is a tool which little else can competition.
However, offers craftsmen a sort of double-edged sword. Since the tools can perform numerous programs, since they’re built in many different sizes with unique attributes, focuses and benefits, picking the best miter saw for your own life and work-load can be unbelievably tough. Accordingly, I have assembled the below information to help guide you (or chemical slide you) in the perfect direction.
Features and Factors
In the end, the first point to think about isn’t always on or about the miter saw whatsoever. Rather, your first thoughts should be on how you’re going to use the tool. How frequently will you use it? What will you will need to cut? Where (store, garage, occupation website) will you work with this? and etc.. Having a plan and a budget before beginning looking seriously for your miter saw can allow you to make a better choice.
The hottest and most universal miter saws typically provide a 10-inch or 12-inch cutting capability. Though you’ll see miter saws with capacities which are both bigger and smaller than this, I recommend most users remain within those parameters.
12-inch sliding compound miter saw offers the best cutting capability, but it is going to also be a more expensive, heavier instrument. Choosing between a chemical and a sliding compound miter saw, then, requires a couple of considerations.
Secondly, the blade moves about 45-degrees into the left and right for miter cuts, and finally, the blade will lean either to the left or to the left and right to do bevel and double bevel cuts.
Although best compound miter saw are typically more mobile and more affordable than sliding compound miter saws, they also have less capability for wider boards. Most often, a compound miter saw will be not able to through-cut a wide board with one pass.
A sliding compound miter saw does all those things a compound miter saw does while also adding a couple more items to the pot. For starters, a sliding compound miter saw is made using two rail-like tubes that allow the blade to move back and forth at a bigger range of motion. This develops crosscutting capacity by a few inches and enables users to through-cut wider boards (usually with one simple pass).
Because of These tubes, however, sliding compound miters saws are usually heavier, they are less mobile and they are more expensive. With the exception of some Bosch and Makita saws that use a sort of articulating arm instead of sliding-tubes, sliding compound miters also need more room (particularly at the back of the saw) to operate correctly.
To get Technical for a very short moment (and using the typical 10-inch compound miter saw and the typical 12-inch sliding compound miter saw (opposite ends of the spectrum to bookend your potential cutting capacities), 10 and 12-inch miter saws usually provide the following cutting capabilities:
Max Reputation Molding: 4-inches – through – 6-inches.
Bevel controls enable users to adjust the angle of the blade to make angled cuts across the depth of a board. This is incredible handy and particularly helpful when cutting molding. Miter saws are available with a single one bevel (single bevel, blade tilts to the left) and 2 bevels (double or dual sided, blade tilts to the left and right).
In Order to create a bevel cut in the opposite direction, single bevel saws require that inventory be flipped end for end (which may be a nuisance). Double bevel saws, on the opposite end, offer easy bevels to both the right and left. While dual sided miter saws are more expensive, the cost difference (about $50 – $100) is nearly negligible if you use the feature.
Controls are conveniently up-front, most saws’ bevel controls are put at the rear of the saw.
To improve cutting capacities, some saws can also be built with slide-out extension cords to support bigger boards. While in theory this is a excellent feature, if you don’t invest in a more expensive tool, these wings are often not all they are cracked up to be. Conversely, on a more high quality saw, they are a definitely a convenient additional.
Some saws are made with the engine fixed over the blade. This makes for simpler bevel cuts (particularly in thick inventory) and typically provides a much better line of site whilst working.
Every miter saw than the few attributes listed above, these points should Help you discover the ideal path to the perfect saw. Between big cutting Capacities, bevel adjustments and sliding-tubes, there’s a miter saw Out there that will perfectly compliment your requirements. Course, brings us right back to our very first consideration – that in the End of the day, the most significant part a miter saw is its operator. Know what you want from your miter saw and go looking for one With those expectations in mind.